Saturday, 4 October 2025

Kemp Street Bridge changes for Inland Rail

 Kemp Street Bridge - the removal

On the weekend, September 13-15th 2025, Kemp Street Bridge in Junee was removed.

Kemp Street bridge in Sept 2023.

The Kemp Street bridge was finally opened on March 8, 1945, after many decades of community pressure to build it.

Whilst I won't be modelling Kemp Street on my layout, the bridge was built in a similar manner to the Edmonston Street bridge in Wagga, that I covered in a blog post in September 2022.  Well, that is my justification for this post, and also an excuse to document this small part of the Inland Rail project, from a modellers persepective.

I am indepted to the Junee Bulletin, particularly for the drone pictures of the bridge's removal.

100 Mile project Facebook page had a picture of the bridge, taken from the opposite direction to my first picture.



Junee Bulletin Drone picture in May 2025, shows Junee yard beyond


My detail pictures from September 2023.  (n.b. to get a bigger image, click on a picture)



Set of steps from Edgar Street to the bridge

Abutment beside Edgar Street

Besides the roadway, and railway, the bridge also crossed a storm water drain





The platform that was for the semaphore signals



Water pipe for the ???  Was this pipe for watering steam locos at Junee station from the water tanks close to the roundhouse? 




There were 4 lamps of this design on the bridge.  I understand that these lamps are to be reused in the replacement bridge landscaping

Signal platform. 





Roadway ramp retaining wall detail, besides the steps up from Edgar street


I was always interested in semaphore signals, and in 1996, well before I moved to Junee, I took this picture of the signals that were part of the Kemp Street bridge until 2007.

Inland Rail changes

Artist impression of the replacement bridge.  The footpath takes a serpentine route to meet new standards to minimize gradients

For the last 2 years, there has been a succession of activity, surveywork, and closures of Edgar Street, whilst detail design work is undertaken, and services relocated.  There was also changes to the train operations being made to limit the length of time trains would be blocking the level crossing near the railway station.  Removal of Kemp Street bridge is a significant bit of infrastructure for the town of Junee to lose for 18 months. 

Image from the Inland rail website shows the current bridge 

Image from the Inland Rail website shows an artist impression of the new bridge.  Double stacked containers requires addition clearance, and was the real reason for removing the existing bridge.  Disappointingly, the pedestrian bridge extension north from the concrete pier is missing from this artist image.  That lack of detail does not give me confidence that they will get it right.

The demolition

The last cars to cross the bridge were on Friday, September 5th.  Workers than started the demolition process, although the main work was to wait until the major railway shutdown on Sept 13-15th.

A sneek peak of the bridge taken Sept 10th, also showing some abandoned infrastructure remaining in Junee yard


My picture on on Saturday, 13th Sept.

    The following images from the Junee Bulletin facebook page















The days after

After all the activity leading up to the demolition, the days following have been a letdown.  There was an erection of a fence, and then nothing.  

From the Olympic way approach to the bridge, it almost seems like you could launch a car, Dukes of Hazard style, up over the ramp to land over the gap

 
Close up of earlier image.

From a slightly different angle

The new bridge is expected to take 18 months to install.  New abutments, piers, and roadway alignments will be needed, along with earthworks to raise the olympic way intersection.  

Other work occuring

The shutdown weekend 13-15 September was a hive of activity on the line from Illabo south, mostly associated with inland rail.  

Whilst travelling to Stephe Jitts's operating session, quickly stopped to observe a culvert being installed just south of Illabo.  Both main lines have been cut, and the equipment was digging out  the channel.  The canola makes a good backdrop

 
Junee Bulletin's drone image shows this a lot clearer


Side projects

Stephe Jitt's operating session (Sept 13, 2025) at Murrumbateman  (2 hrs drive each way from Junee)

I was assigned the Limestone local, which gave me a lot of time to take some pictures.

A 13 class, with a single CCA carriage at Limestone's small platform.  The 13 class is a Craftsman Model kit, restored to DCC operation by Macca.

Down the short branch to the mainline at Violet

Arrival at Kangaroo Valley, where the train terminates

Runaround at Kangaroo Valley station.  Use of the tank loco means no need for turning.

A stop at the cement works.

Mansfield 43 class repair

Many decades ago, I was on a work course in North Sydney, and after the course had finished for the day, I travelled north by suburban train to Mansfield Hobbies, where I acquired a new 2nd run Mansfield brass 43 class direct from David Anderson.  I never got around to painting my model.  So when a painted Mansfield 43 appeared on ebay recently, I thought it would satisfy my need for  painted brass 43  I was successful


  The painting of the model is esquisite, only let down by the cloudy windows.  But the shell hid a problem, that the seller hinted at with a statement that the model didn't run, and whilst the cause was not stated, there was a picture on ebay of a gear tower with a split.

That seemed like a challenge.  I have an spares, replacement gears, and a pair of 1st run Mansfield 43 bogies that might help.  

After removal of the shell, I then disassembled the gear towers.  Besides being overoiled, there was no evidence of any cracked gears, or issues with the gears, bogies, or motor.  There is a fine crack visible on the gear tower case, that didn't appear to be a problem





But, the split gear tower was a symptom of a more serious problem.  The M2 sized screws had stripped the thread inside the gear tower, and closer inspection showed zinc pest deterioration of the casting.  So the metal is weak, and will probably get worse in time.  Anyway, unless I make, or buy a replacement gear tower, the best repair was to add some foil to allow the screws to bite.

The loco is now back together, and runs extremely smoothly with the improvised screw thread repair.  But for how much longer?  I doubt I will fit DCC, so it will head to my display case.

Another trinket for the Train wall.

To all my readers from the USA....here is one for you.  Another recent ebay purchase was a General Electic loco builders plate from a C39-8.  The seller didn't say what loco it came from.  Anyway, to my surprise, my modest bid was successful.

As the plate arrived.  Dirty, and grimy.  The red around the "GE" was difficult to see


A clean in nothing more than detergent, and a toothbrush on the grass outside my train room

    
Slightly damp, the black and red paint really pops

Once dry, the colours once again fade, but the red is now easily seen without the grime



I did some research on the internet, and found the plate was installed to this loco, Norfolk Southern #8640 - here seen at Chicago in 1991.

Now the plate is attached to my display wall, with other locomotive plates, some real, some reproductions

Conclusion

Life often gets in the way of a finding time to devote to my model train layout.  I keep telling myself, it is a hobby, and delays are OK.  But it still is frustrating, although I am certainly getting lots of exercise pushing the mower around, in battle with the extreme grass and weed growth this spring.  I will try and do better for the next blog post.  

Until next time, build a model or two.